VHF AND UHF TRANSCEIVERS   IC-F12  (VHF transceiver, 16 channel type) IC-F12S  (VHF transceiver, 2 channel type) IC-F22  (UHF transceiver, 16 channel type) IC-F22S  (UHF transceiver, 2 channel type) Perfect for Businesses, Big & Small Simple operation with minimum switches Built-in 5-tone, CTCSS, DTCS encode/decode plus DTMF encode MIL specification rugged construction 16 position rotary channel type or 2 position toggle channel type Powerful 5W of VHF and 4W of UHF output power Selectable 12.5kHz or 25kHz channel spacing Optional Ni-MH battery pack or alkaline battery case available Wide range of accessories available SPECIFICATIONS  GENERAL Frequency range :  IC-F12/S   146-174 MHz IC-F22/S   400–430 MHz 440–470 MHz Channel spacing : 12.5/25kHz or 20/25kHz Number of channels : 16 (rotary type) 4 (toggle type) PLL channel step :  IC-F12/S   2.5kHz or 3.125kHz IC-F22/S   5kHz or 6.25kHz Power supply requirement : 7.2V DC Current drain (approx.) 　Tx High (VHF/UHF) 　Rx Rated audio 　     Standby : 1.6A   250mA   70mA Frequency error : ±2.0kHz (wide, middle)   ±1.5kHz (narrow) Operating temp. range : –25°C to +55°C Dimensions (proj. not included) : 54(W)Ч128(H)Ч37(D)mm Weight (with BP-209) : 310g    TRANSMITTER Output power (at 7.2V DC) : IC-F12/S   5W, 2W, 1W IC-F22/S   4W, 2W, 1W Max. frequency deviation : ±5.0kHz (wide)   ±4.0kHz (middle)   ±2.5kHz (narrow) Spurious emissions : 0.25µW (below 1GHz) Adjacent channel power : 70dB (wide, middle)   60dB (narrow) External mic. connector : 3-conductor 2.5(d)mm /2.2kΩ    RECEIVER Sensitivity (at 20dB SINAD) : 0.63µV typ. emf Squelch sensitivity : 0.3µV typ. (threshold) Adjacent Ch. selectivity : 70dB (wide, middle)   60dB (narrow) Spurious response : 70dB Intermodulation rejection : 65dB Audio output power (at 7.2V DC) : 500mW typ.   (at 5% distortion with an 8Ω load) External SP. connector : 2-conductor 3.5(d)mm /8Ω     Supplied accessories Battery pack; BP-209 Belt clip; MB-74 Antenna Applicable U.S. Military Specifications Standard MIL 810C MIL 810D MIL 810E MIL 810F Method Procedure Method Procedure Method Procedure Method Procedure Low pressure 500.1 I 500.2 I, II 500.3 I, II 500.4 I, II High temp. 501.1 I 501.2 I, II 501.3 I, II 501.4 I, II Low temp. 502.1 I 502.2 I, II 502.3 I, II 502.4-3 I, II Temp. shock 503.1 I 503.2 I 503.3 I 503.4 I Solar Radiation 505.1 I 505.2 I 505.3 I 505.4 I Rain 506.1 I, II 506.2 I, II 506.3 I, II 506.4 I, II Humidity 507.1 I, II 507.2 II, III 507.3 II, III 507.4 - Salt fog 509.1 I 509.2 I 509.3 I 509.4 - Dust 510.1 I 510.2 I 510.3 I 510.4 I Vibration 514.2 VIII, X 514.3 I 514.4 I 514.4 I Shock 516.2 I, II, V 516.3 I, IV 516.4 I, IV 516.5 I, IV Measurements made in accordance with EN 300-086. All stated specifications are subject to change without notice or obligation. Back to Top